Category: Uncategorized

Tiny Sophia Bag HACK: Travel Sanitizer Holder

As the world goes on, we know washing hands and using sanitizer is LIFE right now. It is SO important to stay healthy and protect ourselves against all germs – pandemic or not!  Washing hands with soap is the preferred way to keep them clean, but when there isn’t a sink around hand sanitizer is a decent alternative. You can read more about the benefits of hand-washing here with the CDC.

Like all of you, I want to keep my family safe and have sanitizer on them at all times – especially as school opened up for my kids. But of course, supplies have been (and still are) very bare.  Trying to find those manufactured jelly style travel sanitizer holders was just impossible. That’s when I took it upon myself to make cases for my kids and husband.

Different size travel bottles

It turns out that the Tiny Sophia Bag (read about it here) is the right width to hold most travel sanitizers! The height just needs to be adjusted and that’s where this hack was born. This hack will take you through the steps to transform your #tinypurse to a sanitizer holder for most 1-2 oz travel bottles.  I tried to find a variety of bottles to test so you can see how they fit and decided to create one version for bottles from 1-1.6 oz and then another version that can fit 2 oz bottles.  If you are using bottles different from any of those pictured, be sure to check the template against your sanitizer BEFORE cutting any material.

2 oz Holder vs 1 oz Holder

 

 

Materials Needed:

  • The Tiny Sophia Bag pattern – found here
  • Ruler
  • Extra paper
  • Marking Instrument
  • Clear Tape

Tutorial

***Please note there are adjustments depending on whether you are making a holder for a 1.0-1.6 oz. bottle versus a 2 oz. bottle.   Please read instructions carefully.

1. Cut the pattern template out per instructions. Mark the cut line along where the bottom flap meets the sides.

2. Take a scrap piece of paper (wider than the bottom flap) and mark a 1″ high extension for 1-1.6 oz. sanitizer bottles. *If you have a 2 oz. bottle, you will want to mark a 2″ high extension.

3. Cut the bottom flap off the bag template following your markings

4. Line up the top of the pattern along the extension and tape into place.

5. Take a ruler and mark the right side of the extension aligning it to the Top flap’s side edge.

6. Repeat on the left side of the extension.

7. Line up the bottom flap to the lower side of the extension making sure it matches the side markings.

8. Trim away the excess paper.  Mark a line 1/2″ from the top of the extension. *If you are making a 2 oz. bottle holder, mark a line 1″ from the top of the extension.

9. Use a sanitizer bottle cap as your opening.  (This replaces the Charger Opening.)  Center it vertically on the template and place it just under mark made in the previous step.  Trace.

10. Carefully cut out the circle with paper scissors.

11. Check that the sanitizer bottle you want to use fits through the opening on the template. Adjust as needed.

12.  Check that the template fits around the bottle by aligning the hardware holes.  Adjust as needed.  Once you are satisfied with the fit, follow the steps in The Tiny Sophia Bag to finish your  travel sanitizer holder!

Notes:

This cork version uses the 1 oz adjustment, but if I were to make it again just for this style of sanitizer bottle from Bath & Body Works, I would make a slightly wider opening to accommodate  that wider flip-cap.

I added stitching to all of my samples in this post, but you don’t have to.  Using faux leather with felt backings like these pictured above leave no fraying and make this a fast and simple project.

With the holidays ahead, these will make such great gifts!  So I will switch up the hardware to swivel clasps on the back so they can hang easily from key chains, purses and backpacks.

Where to find supplies:

  • For Cork or Faux Leather, I’m a big fan of Sew Sweetness.  Shipping is flat-rate, fast and I think a great deal!
  • For real leather and a variety of finishes, TanneryNYC has remnant bags.  I received small – medium sized cuts and was able to make several Tiny Sophia Bags out of the surprise shipment. These are high quality pieces of soft leather.
  • I love Emmaline Bags and By Annie’s hardware, but if you are looking for a value set for kids, I recently bought these (pictured on yellow case) and these from Amazon.
  • For Snaps, I used spring style ones from Gold Star tool, but recently fell in love with these Rivet Magnets from Kam Snaps (as seen with the pink cork version above.)

 

I hope you enjoy this hack and find it useful in our current environment.  Please drop a comment and let me know what you think!

 

Hugs and Stitches,

Cristy

 

This post may contain affiliate links.  Any earnings go right back into powering this website.  Please read my Disclosures here.

#SewPink Blog Hop with the Erin Backpack

19 Comments

October is Breast Cancer Awareness Month, and with 3.5 million women in the US with a history of current and/or past treatment, we all have someone close to us who has been affected.  Unfortunately, I’ve seen my aunt suffer and pass away from this disease and also continue to see more and more friends go through their own personal battles.  It’s so difficult to see anyone suffer and knowing that I am personally at higher risk – as an aging woman. That is why I’m SO proud to be part of the By Annie #SewPink Initiative to bring more awareness to this cause.

The #SewPINK Blog Hop has been taking place all this month to raise awareness for breast cancer and breast cancer prevention. You can follow the hashtag on social media to follow along!   By Annie’s is even running a photo contest here and released a great FREE pattern which you can find here.  These are great ways to get involved and the pattern is a nice and easy sew with your friends and/or guild.  On top of all of these activities, By Annie’s has graciously offered to provide a $30 shop credit to one of you!!!!  (Details are below.)

Earlier this very year, my OB/GYN told me I’ve hit the age where I need to start getting mammograms.  (‘Nothing like getting older, right?)  85% of new cases happen to those who have NO prior family history (due to genetic mutations) so early detection is key!  (Source: www.breastcancer.org )  But just like everything else that has also happened this year, my appointment was put on hold. Getting the call to be part of the #SewPink Blog Hop really gave me the push to get a screening back on my schedule and I am so very grateful! I hope you do the same and check out available screenings below:

Project

For my Blog Hop project, I made the (soon to be released) Erin Backpack. This is a design I’ve been working on and off again for over a year — OK, it’s been more off, then on but it will be released by end of year!  This is a spacious backpack with a half moon design that also converts to an over-the-shoulder or crossbody bag.  It is large enough to be used as a diaper bag or just for some day-tripping.

I wanted, of course, to make my backpack PINK!  This is not a color I use often in my sewing and definitely not as a focused hue.  So, I chose this great Tula Pink quilt cotton for it’s beautiful marbling of pinks and purples balanced on a natural background. The lining is also from the same collection and I just love that deeper shade of magenta with the swans.  Who wouldn’t love some swans?!?

The structure of the Erin Backpack is based on By Annie’s amazing Soft and Stable product.   I’ve been such big fan of this stabilizer for awhile and appreciate the firm shape it creates beyond other interfacing — especially when using a lighter substrate like quilting cotton as seen in this kid’s bag here and should bag seen here. Soft and Stable is also wonderful in how it provides great stability but is also soft and pliable.  Most domestic machines can sew through this quite easily!  The last thing I’ll gush about is how I love the loft of this product and how it could also provide so much great texture.  I used it on my favorite duffle bag (EVER!) you can find here.

By Annie’s also has so many other great purse accessories. I knew I had to try out some of the hardware!  The swivel clasps and triangle rings in the antique brass finish were perfect for my project. They went well with the leather details and balanced with the metal zippers.  The hardware is nice and sturdy and definitely feels like it will hold up well over time.

For the strap, I use my Guitar Strap tutorial and FREE pattern templates you can find here.  (You’ll notice I made a change for this strap to be adjustable…which is the addition of an extra rectangle ring.)  Inside the strap, I also added By Annie’s 1.5″ wide Strapping to add more strength and heft when wearing this backpack.  This is a nice large bag and I wanted to make sure the weight when filled up doesn’t make the straps dig into my shoulders.

Inside Erin, there is room for a large zippered welt pocket and 5 separate slip pockets. Since this bag can be used for virtually anything, I wanted the lining to serve as more organizational than just storage.  This way,  you can hold larger snacks water bottles, books and even craft projects inside!

But in a large backpack, it can be hard to see all the contents which is why the By Annie’s Lightweight Mesh is so wonderful.  You can check out everything in your pockets at a glance and I love that there is a little stretch for anything you may want to carry. The top edge is finished with Foldover Elastic and was a breeze to sew with my coverstitch, but any zig-zag stitch would work as well.

I hope you enjoyed my PINK Erin Backpack for the blog hop.  Its pairs perfectly with my rose gold phone and hacked Tiny Sophia Bag, don’t you think?

Contest

For your chance to win $30 shop credit to By Annie’s, please comment below.  I’d love to hear your connection with breast cancer.  If your own story is too personal, let me know how you like my project or share your own bag-making journey.

Giveaway will be open until 10/31/2020 and open internationally.  

2020 Blog Hop info:

Schedule –

Message from By Annie’s:  “The #SewPink Initiative was created by ByAnnie.com LLC to raise awareness for breast cancer throughout the year. Our efforts culminate in an annual blog hop during October’s Breast Cancer Awareness Month to promote self-care, awareness, early detection and support for those affected by breast cancer.” 

To learn more and see the calendar of events visit: https://www.ByAnnie.com/SewPINK

 

Bag making products, as mentioned, were provided for this post By Annie’s as part of the Blog Hop.  The Erin Backpack is my own design.  All reviews and opinions are my own. For my full disclosures, you can read about them here.

Review: Sirocco Jumpsuit in Luxe Green Scuba

2 Comments
This post was originally written for the Minerva Crafts blog in November, 2019. Additional edits have been made after real-life wear of the garment.

Intro 

Hi, this is Cristy Stuhldreher from Love You Sew with my very first #MinervaMake as a blog contributor!!!  I was SO excited to be invited to be part of such an extensive team of bloggers here and equally excited to play with so much beautiful fabric.  My first find was this gorgeous Lady McElroy Luxury Plain Scuba Jersey Knit Fabric in Bottle Green.  With autumn (my favorite season!) quickly coming to the States, I knew I would need to get ahead and make some transitional garments with the switch of temperatures that are bound to come.  So, after I saw this scuba fabric I immediately thought of the Deer and Doe Sirocco Jumpsuit (like many other contributors already have!)

Fabric

This Lady McElroy Luxury Plain Scuba Jersey Knit Fabric was such a great find!  I’m a big fan of Ponte de Roma fabrics and knew I would love Scuba just the same since they are both heavy double-knits.  They feel and act very similarly, but are made of different fibers.  Scuba is generally poly and elastane whereas Ponte is generally viscose and elastane.  This soft and smooth Scuba Jersey did not disappoint with its great stretch and nice body which is perfect for a jumpsuit when you don’t want every bodily imperfection to show through.  It is also works SO well for a knit jumpsuit with amazing stretch and recovery.  The last thing I would want after all of this hard work would be a saggy stretched out butt!
It’s always hard to tell how color will come out in person versus on a computer, so I was a bit nervous to see how the Bottle Green would be.  It looked slightly more muted, like a deeper sage green on my screen.  But I was actually delighted  to see that the fabric was more of a deep rich gem tone – a solid “Hunter” green, in my opinion.  With my olive skin and dark hair, I love a gem tone- especially for the colder months ahead!  After a few washes, the color has stayed true to the first day it arrived on my doorstep – love that!
With this fabric being a double-knit, I would recommend using a ball-point needle and your stretchiest stitch found on your machine (zig-zag, triple-zig-zag, lightning bolt, etc.)  I used a combination of my overlocker and coverstitch to allow my jumpsuit the greatest amount of stretch to fit larger hips.

Pattern

Jumpsuits still look to be on trend a little while longer, so I thought it was safe to make the Sirocco Jumpsuit for the fall.  With the short-sleeves and full pant legs (on View A) I figured this was a great garment to wear on the cooler nights downtown with or without needing a jacket.
The Sirocco is a unique pattern in that there are no ties or other fasteners used to get in and out of the garment.  You slip in and out of it all through the faux wrap V-neckline.  This might not pose a huge deal for most, but I have hips which are two sizes larger than my waist –which means I REALLY will need to stretch out the waist to maneuver around.  This is the main reason I chose the heavy Scuba fabric to handle the severe stretching over my hips.  As I was fitting the garment, I honestly thought I would have to put in a side zipper for my hips, but the Lady McElroy Luxury Plain Scuba Jersey Knit Fabric proved to have such amazing stretch and recovery that I didn’t need it!  Honestly, I feel like I could wear this all day long…even after multiple bathroom breaks!
I made a few modifications for my SHORT 5’3″ frame with those aforementioned HIPS:
  • Made a 40 bodice and graded to a 42 in the hips and back to a 40 for the rest of the leg
  • Shortened bodice by 1/2″ and used a chainstitch (from my coverstitch) to secure the seam allowance down since the fabric is so lofty – This allows the lapped bodice to stay secure over your chest.
  • Shortened pant legs by 4″ initially (by just tissue fitting) and then took an additional 3 3/4″ when it was time to hem so that it would hit right above the ankle bone – Next time, I will shorten at the thigh and also from the ankle to get a better fit around the knee.
  • Extended the crotch length 3/4″ on both the front and back pant
  • Deepened the seat on the back pant by 3/8″
  • I wish I took out an 1″ out of the rise before cutting, but was able to take 1/2″ out of the overall inseam to narrow the legs and decrease the rise.
  • Took an additional 1″ out of the ankle and blended up to the knee for a slimmer leg

After these changes, I can’t tell you how incredibly pleased I am with my Sirocco Jumpsuit.  The Lady McElroy Luxury Plain Scuba Jersey Knit Fabricis so chic and the deep green really does make the Sirocco Jumpsuit so “EXTRA!”  Love it!!!
You can find my other makes on the Love You Sew Blog (here!) and more daily inspiration on Instagram @loveyousew_ .

 

Happy Sewing!

Cristy

 

 

Affiliate links are in this post. Check out my Disclosures here. Fabric was provided for review as part of the Minerva Maker Blog Team.  All thoughts and opinions are my own.  

 

Add Puff Sleeve Drama with a Sheridan Sweater Hack

This post was originally published on the Hey June Handmade Blog in January, 2020.  Edits are in italics and additional pictures have been added (since I love this pattern SO much!)

When I first hacked this Sheridan Sweater for the Hey June Handmade Blog, I had no idea it was going to become one of my MOST worn tops. Prior to March, life was pretty normal while we were just starting to hear about the pandemic. My social world was still moving along and was able to wear my Sheridan to Lunar New Year celebrations (as planned!), Galentine’s Day fun with my girls, and was my go-to for a night out.  I knew even back then that I wanted another Sheridan.

After a #sewingfail with the wrong fabric (it was a red and cream colored stripe that clashed and looked HORRIBLE with my skin tone and hair highlights,) I was ready to make another.  This time I wasn’t going to mess around.  I knew I would ADORE my new Sheridan because I used…the same hack…and the same fabric as my OG…just a different color!

 

Back in early December, I knew I needed a new red top.  My one cardigan just wasn’t enough for all of the holiday school parties, concerts, church events and even family get-togethers.  I wore that one piece of red clothing OUT and knew I needed something else to add to my festive wardrobe.  But did I really need a new top???  Did I really want to make one??? Then the Sheridan Sweater was launched and my questions were answered.

All of my internal fighting against wanting “another” knit top disappeared.  After seeing the Sheridan launch, my mind switched and I bought the pattern right away.  Of course, I need  a new red top!  It WILL work through the holiday season, AND into the Lunar New Year AND be useful for Valentine’s Day school parties!  Why wouldn’t I need the Sheridan Sweater in my life?!?

Adrianna did a fantastic job designing the different views and I’m obsessed with the seamless funnel neck, which I haven’t seen in any other DIY pattern.  The Sheridan Sweater also has the big statement sleeves which is on still on trend and I knew both of these features would really stand out in red.  But since this was going to be my all-winter holiday top, I wanted to bring it up juuuuust an extra notch.

FABRIC

I found this beautiful textured waffle knit from Telio fabrics.  One of the reasons this sweater has been on constant wardrobe repeat is the fabric.  As a poly/spandex blend, the color saturation is on point.  After all of the washing and drying I’ve done, the color still looks as intense as day one.  I was concerned that the texture might be lost over time with dryer heat, but it’s all still there!

The Paola Pique Liverpool’s medium weight was a perfect complement to this pattern.  It has great body and really shows off the full sleeves.  The stretch and recovery is also very nice.  When I pull up on the sleeves and adjust the waistband, it  holds it’s size well and doesn’t stretch out over the course of the day.  This fabric comes in so many rich jewel tones that I had to have the Emerald.  The pictures come up more teal, but this color swings more to the green side in-person.

TUTORIAL

I figured if I was going red, I wanted to make the sleeves stand out even more. So….I hacked the sleeves to be more voluminous in the sleeve head for All. Of. The. Drama.  Below is my quick and definitely non-technical way to achieve that extra shoulder poof.

1. Take the sleeve pattern and make a copy.  (I traced the pattern onto some Swedish tracing paper I had on-hand.  I like using this since it’s more pliable than regular paper and can be pinned/sewn without being destroyed.)

2. Divide the sleeve into approximately 4 equal sections by width.  With the nice notch markings already drafted as part of the pattern, I used these as guide when splitting the sleeve.

3. Cut the pattern to separate these sections from the sleeve head all the way down to the cuff, but NOT cutting through.  All of the sections should be hinges and able to move.

4. To start, I added 1” in between each section.  I placed scrap paper underneath the pattern, and hinged each section out by 1” at the sleeve cap.  Then I taped the pattern onto the scrap.  Repeat 2 more times between the sections.  If you would like more volume, you can increase the hinge widths.

5. To get the extra volume at the top of the cap, I added 3/4” to the top and blended the line back to the notched parts of the cap, all while following its shaping.  Again, if you want a little more puff in the sleeve cap, feel free to add a little more to length to the top.

6. At the cuff line, true up the pattern so it is straight again.

At this point, I cut out the pattern and did make a muslin, but only had quilt cotton on hand.  It gave me an idea of the extra volume and shape added to the sleeve.  I did have to consider the extra weight and stretch with the knit fabric.  But it was still good enough for me and I went ahead to cut into the main fabric.

To insert the sleeve, I made gathers between the sleeve notches not exactly knowing how it would all look.  But I ended up marking 3” on either side of the shoulder seam and pushed all the gathers in between those markings.  I basted the sleeve into place and was very happy with the result!  With that, I finished sewing the sweater and have never been more pleased!

This hack turned out exactly like what I wanted and just love how “extra” the sleeves are.  The additional gathers and volume in the sleeve cap really balance out the overall ease in the sleeve and I love the extra long cuff to show it all off.  This top is pretty fancy and ready for every occasion now.  It’s still comfy in a stretch knit, but also so incredibly unique and special!

Project Summary

  • Pattern: Sheridan Sweater by Hey June Handmade; View: B; Size 10
  • Mods: Narrowed shoulders by 1/2″ each, increased the cropped length by 1″, used Puff shoulder hack above
  • Fabric: Telio Pique Liverpool Knit from Fabric.com in Hermes Red and Emerald

This hack can be used on just about any pattern with a set-in sleeve.  I may have to try it on a woven pattern this fall/winter.  Please let me know in the comments if you use this hack!  I would love to hear what you think!

 

Hugs and Stitches,

Cristy

 

This post may contain affiliate links.  You can read my full Disclosure here.

 

Emma Stadium Bag Hacks with Twill Tape

The best part about writing patterns is coming back and hacking them! I’m constantly inspired by the runways and the latest fashion trends. When I wrote this Emma Stadium Bag hack for Sewn Magazine (April 2020,) I noticed how straps were becoming the main focus on bags. They were produced in different fabric from the main bodies and were made in all sorts of distinctive colors and contrasting patterns…making the straps REALLY stand out.  Many brands were  offering customization with mix and match options which help to make a bag feel like it was made for you. I love a good statement strap as seen with my Guitar Strap Tutorial here and my play on a fringed Festival Bag here.  Needless to say, I couldn’t resist making my own designer inspired version.  Can you guess the high-fashion label that was my muse?  Now, you can really make a full personalized bag with the Twill Tape hack below!

Materials Required

Cutting

  • Cut fabric and vinyl per instructions minus the strap pieces.
  • Cut (2) 7 1/2” lengths of the Twill Tape. Heat seal each end of the tape with the lighter. Set Aside.

Strap

  • With the remaining Twill Tape, heat seal each end of the tape with the lighter.  *If you are using a 100% cotton tape, you won’t be able to heat seal.  Sew 1/8″ at each raw edge to keep it from unraveling.  Back-stitch well.
  • Follow the instructions in the pattern to thread the strap through the 1 1/2” slider and (2) 1 1/2” Swivel Clasps.
  • Use (2) Rivets to secure each end of the strap (4 rivets total) or sew into place.  This video can help you through adding rivets.

Pocket

  • This was omitted to let the twill tape stand on its own and not detract from the overall look.

Zipper Top

  • Make with the SHORT D-Ring tab option.  Although the photo shows the vinyl already attached, you will only have the Zipper Top completed at this point.

Vinyl Bottom

  • After marking the center of the vinyl bottom on the wrong side of the vinyl, mark 3/4” out on either side of the center. These lines will be used as sides for the Twill Tape.
  • Flip the vinyl over and line up Twill Tape within the markings. Top-stitch along the Twill Tape 1/16” into place. Optional – Add another row of stitching down the center of the Twill Tape. Repeat on other side of the body.
    • TIP: Sew down the sides of the Twill Tape in the same direction to avoid possible shifting.
  • Finish sewing the rest of the vinyl bottom, making sure to align the Twill tape when sewing the bottom seam.
  • With the Twill Tape facing up, sew the seam allowance to the body between 1/8″ – 1/4″ from the seam.
  • Finish the bag and wipe away any markings on the vinyl.

D-Ring Accent Tabs

I love the look of extra texture on the Zipper Top and these tabs provide such nice details…especially with the addition of rivets.  However, if you tried to make only these long tabs with fabric, they would pull and go vertical when worn.   The D-ring would also be sliding all across the tab and the weight distribution on the strap would definitely be off.  So when I was trying to decide how I could I could have the look, it dawned on me, that I could literally combine the techniques of the short tab and these riveted accent one.   I developed this “double D-ring” method to have the visual appeal AND have the security of a shorter tab.
  • To make, take the 13”x1” strip of fabric –
    • (Bottom and middle strips) Fold each long side toward the center, wrong-sides together making 1/2” single-fold tape.  Press well
    • (Top strip) Top-stitch 1/16” along each long edge
  • Cut in half length-wise so there are (2) 6 1/2” tabs. With each tab, fold each short end inward with wrong sides together by 1/2”.   Press.
  • Fold the entire tab in half, wrong sides together.  Press.
  • Glue down each 1/2” folded end.
  • Slide the Accent Tab equally through the 1/2” D-Ring with right side facing out.
  • With the D-Ring tab fully extended, mark the Accent Tab placement so it is parallel to the zipper and next to, but not pushing into the D-Ring.  Glue the Accent Tab into place.
  • From the edge of the tab, mark at 3/8” and 1 1/4” for rivet placement.
  • Use the fabric hole punch to cut through the Accent Tab, Main Fabric, and Lining.  Attach rivets using your preferred method.  You can check out this hand application video here.
  • Repeat on the other side of the same Accent Tab. Then repeat for the second Accent Tab. You will attach 8 rivets altogether on the Accent Tabs.
  • Attach the Strap to the D-Rings and you are ready to rock out in style!  How do you like the D-ring illusion?
If you are looking for other ideas to get the most out of your Emma Stadium Bag pattern, check out this post on how to add a leather hook and the Intro post here with tester versions.   Happy Sewing! Cristy  
This post may contain affiliate links which help keep this website and content rolling.  You can read about all of my Disclosures here.