When wearing a waist (belt, bum, fanny pack) bag, space is incredibly limited. There is already a nice built-in slip pocket to the Kelly Waist Bag (a FREE pattern you can find here.) But I thought I could kick it up a notch and add some card pockets — perfect for just that ID and credit card for a night out. The smaller slots keeps your cards more secure, yet easily accessible.
Make the Card Pockets
This is a very quick and simple add-on to the pockets. You will need the pattern which you can find here, plus an additional 6″ x 2 1/2″” piece of leather which I’ll refer to as the Card Pockets.
With the 6″ x 3″ Card Pocket, mark a line down the center with right side facing up. Take the Front Pocket piece and lay it right side up and then lay the Card Pockets with right side facing up aligning the bottom edge and corners. Clip into place.
Sew on top of the Card Pockets on the marking attaching the Card Pockets to the Front Pocket and also dividing it into two.
Continue to Step #6 to finish assembling the rest of the pocket.
Project Summary
Pattern: Kelly Waist Bag
Fabric: Sew Sweetness Faux Leather and Cheetah Cork (aff link)
I hope you enjoyed this simple tutorial to add card pockets to your Kelly Waist Bag! You now have an extra layer of storage while being hands-free. Head to the Pattern Resources page for all Love You Sew pattern hacks!
Hugs and Stitches,
Cristy
This post may contain affiliate links which helps keep this website going. You can read all the info regarding these links in my Disclosures.
When I first designed the Emma Stadium bag, it was solely for attending football games. I remember making the bag the night before we had to go out of town and was trying to save as much time (and money – in eliminating hardware) by adding in these leather hooks in lieu of D-rings. But it turns out, you loved my time saving feature when I showed this bag on Instagram. I wanted to make sure I shared the tutorial with you!
After making more of these Emma Stadium Bags during the pattern writing process, I knew these were going to be my handmade gifts of the season –as cosmetic bags! These are so quick and easy to make especially when you leave off the D-ring tabs since there isn’t a strap. You can read more about the Emma here and get some vinyl sewing tips here.
Make the Hook
To use the Emma as just a cosmetic/travel pouch, you will need the small version of the pattern which you can buy here and the following supplies (aff links):
5″ x 1/2″ Leather Hook (you want a more thick, rigid hide to hold up on its own.)
1. With the leather hook, measure from the short end and mark at 3/8″ and again at 7/8″ (There should be 1/2″ between marks.) Repeat on the other short end.
2. Use your hole punch to cut 4 holes at every mark making sure you are centered width-wise.
3. With your completed Emma Stadium Bag (with all tabs omitted,) mark 1 1/2″ in from the side seam. Make another mark centered width-wise on the fabric accent. (This is approximately 3/4″ down from the zipper.) Repeat on the opposite side of the bag.
4. With the fabric glue, add a sparing amount to the wrong side of the leather hook around the holes punched.
5. Lay the leather hook against the fabric aligning the short edge to the vertical mark and the holes with the horizontal mark.
6. Repeat on the opposite side of the bag and hold in place until the glue is completely dry.
7. Using the holes cut out of the leather hook, punch a hole through one layer of fabric and one layer of lining. Repeat for the remaining three holes. If you are using manual hole punches, make sure you have cutting board inside the Emma to prevent you from cutting to the other side of the bag.
8. Add each set of rivet through only one layer of fabric and one layer of lining. Repeat for the remaining three sets of rivets.
9. Use setting tools to affix the rivets together.
Congrats on your chic new travel cosmetic pouch!!!
I hope you enjoy making these quick and easy travel cosmetic bags! These have definitely been a huge hit among my family and friends…I’m having a hard time keeping up with the demand!
Don’t forget to share your makes on social media with #emmastadiumbag and #loveyousewpatterns so I can see all of your fabulous creations!
Hugs and Stitches,
Cristy
This post may contain affiliate links which helps to keep this website ticking. Please visit my Disclosures page to learn more.
The Abbey Convertible Backpack is my go-to bag when taking day-trips with my kids. I like having it out of the way but still being able to hold the essentials. But being a designer, I constantly have new ideas and wish there were different features with every bag I own.
On the back of the Abbey, there is a slip pocket. I added the feature with the intention that it would be a quick spot to hold your phone or keys without having to open the main compartment as frequently. But since I happen to wear my bag more as a backpack, I have to swing it around to access the pocket and felt that a slip pocket just isn’t as secure for an expensive smartphone — and BOOM, I have the idea for the back welt pocket hack.
Back Welt Pocket Tutorial
You will need the original instructions and templates for the Abbey Convertible Backpack which you can find here. Additionally you will need:
6″ Zipper
8 3/4″ x 12″ Lining Fabric + Interfacing (this is large enough to fit an iPhone 7+ with a thick Otterbox case.)
To make the Back Zipper pocket, you will omit all of the fabric and interfacing for the Slip Pocket and move through Step #41. (Please note I don’t have connectors added to my handle base at this point since I used leather and added them later.)
Draw a rectangle measuring 6″ x 1/2″on the wrong side of the Pocket Lining centered and parallel to the short side as shown. The Zipper will run vertically. There should be 1 3/8″ above and below the rectangle and 3/4″ space to the right.
Line up the Pocket Lining as shown with the right edge 1/2″ in and up 1/4″ from the sides of the Handle Base. Pin the Pocket Lining in place. Go back and follow Steps #21-28 to finish the pocket! Voila – a chic looking vertical zipper pocket to keep your phone or other valuables a little more safe as you sling the backpack around.
Since the Pocket Lining hangs vertically instead of horizontally, the weight of a phone would make it drag awkwardly and pull on the zipper. So, the Pocket Lining needs to be anchored horizontally so the weight can hang straight down naturally. To do this, flip the back of the bag right side up and sew directly below the Handle Base from corner to corner catching the Pocket Lining. Back-stitch well.
This is the wrong side after securing the Pocket Lining. The weight of the phone is evenly distributed and won’t distort the structure of the bag.
Additional Modifications
You know I cannot resist using leather in my personal bags! I had this great glazed black upholstery leather I got from Tandy which I used to make a few Kelly Waist Bags. The scraps are great for all of Abbey’s accents like the connectors, handle and closure tab.
I also used my other Abbey Backpack Zipper Cover and Button Stud Hacks which you can find here. I like the clean look from the front and just love using button studs with leather.
I hope you enjoy this hack and even use it for other projects! Don’t forget to use #abbeyconvertiblebackpack and #loveyousewpatterns on social media so everyone can see your fabulous makes!
Hugs and Stitches,
Cristy
This post may contain affiliate links which I use to keep this website pumping along. Please visit my Disclosures page for all the info on my affiliate relationships.
All of my sewing patterns are named after my nieces. Once a pattern releases, the namesake always gets a complimentary bag of her very own. But then, I was in a bit of a predicament when I named theMaya + Harper Travel Changing Set after my 4 and 2 year old nieces. What were were they going to do with full-size diaper changing sets???
I checked with my sister and she assured me there would not be a need for additional sets for her personal use. (Haha – Wishful thinking on my behalf!) But shortly after the pattern’s release, my nieces got their first Bitty Babies and the light bulb went off. I would make Maya and Harper “play” versions for their little babies!
First, you will need the Maya + Harper Travel Changing Set found in my pattern shop here. You will need the instructions for reference and the pattern templates. I highly suggest you make a full Changing Set first to understand the construction and assembly of the Pad and Clutch. Once you get comfortable, you can make the following changes to make this pattern kid-friendly.
Make the “Play” Changing Pad
First thing’s first. You will need to print out the pattern templates at 85%. This will shrink down the pattern enough for most typical baby dolls. Unfortunately, my kids were more into stuffies than dolls, so this 12″ bear will need all the diaper changing 😉
All construction steps remain the same. You will align the closure to the bottom line of the “Tab Placement” and cut your hook and loop fastener to match the Tab width. The finished measurements of the Pad should be approximately 20″ x 12″.
Make the “Play” Diaper Clutch
As with the Changing Pad, you will print out the pattern templates at 85% and cut out all the pieces except for the Strap (you will cut an entirely new piece.)
For Supplies:
Use a 7″ Zipper (at least 8″ overall) and omit the 9″ Zipper
Omit the D-Ring, Swivel Clasp, and Magnetic Snap (for a less fussy look, but feel free to add them back in for a fancier set!)
Add 2″ piece of hook and loop fastener
Cut 13″ x 3″ fabric and interfacing for a sew-in Strap
To make the Strap, follow steps #1-5 to double-fold and top-stitch it. Fold it in half with raw edges aligned. Baste ends together at 1/8″ and set aside.
Starting at step #12, make the Welt Pocket as instructed with a 7″ x 1/2″ Zipper opening and use the 7″ Zipper.
Since the Magnetic Snaps have been omitted, start at step #22 to center the hook and loop fasteners at the snap placement points with the length running parallel to the Zipper. Sew 1/16″ all-around the fasteners.
At step #26, replace the Strap with the D-Ring Tab. Keep the raw edges aligned so the Strap will be completely sewn-in later.
Finish the rest of the clutch by folding up each pocket by 4 1/2″ instead of 5 3/4”. Top-stitch, press and you’re little one is ready to practice parental duties!
Although my sister didn’t need another Travel Changing Set, I think this would be a great Mommy and Me set for yourself or for a friend who is expecting her 2nd+ child! I hope you enjoy making Maya and Harper Changing sets for all the kids (and parents) in your life!
The Claire Fold-over Clutch was my very first published pattern just over a year ago. I can’t believe it’s been that long already. I put my own twist on the popular bag style with a large easy access pocket on the back and the simple use of leather one side of the bag – making it easier to sew. You can read more about my design here and see lots of different versions with #clairefoldoverclutch on Instagram.
My designs are meant to be practical, but also chic enough to work with new trends and fashion with just a change of fabric. This is the case with the Claire. Although it was written to use both fabric and leather, I thought it would be fun to make a full leather version — in cobalt blue for a real statement bag. This blue leather is pretty edgy and gave me rock ‘n roll vibes right away. So, I thought a guitar strap would give the bag a new look all on it’s own…even after making dozens of other Claire Fold-over Clutches!
This amazing woven tapestry-like ribbon was found at a yard sale a few years ago. I think I bought it for $1-2 and was drawn to the bright blue edges contrasting against that moody floral motif. I like mixing up new and old looks, so this trim was definitely all me. The leather was picked up from a destash group and so I was able to grab an amazing deal. The seller was getting out of her baby shower business and had so many pretty pieces of leather to get rid of. Her loss was definitely my gain!
Make the Claire Fold-over Clutch
To make the bag itself, you will need the pattern and instructions from my shop here. The main modification I made was to use leather on both sides of the exterior, instead of just one. (I would only recommend this ONLY if you have a machine strong enough to handle all of the layers.) But if you are just beginning, try out an all fabric version or one with very thin leather/vinyl.
Since the bag is made of solid color all around, I made sure to add in some accents and interest with metal. I used metal zippers (which I actually installed at the wrong places — I should definitely remember to read my own instructions…but I thought going from memory was good enough. Wrong!) If I was using fabric, I would have swapped out the zippers, but with leather, the needle holes are permanent and I didn’t want to mess with all of that and just moved on! In light of my zipper faux pas, I added a line of rivets along the top zipper (through the lining) to play with the same edgy feel of the cobalt leather. What do you think?
Make the Guitar Strap
For the strap, you will need the pattern pieces below. I drafted the ends for 1 1/2″ or 2″ wide straps. Anything else more narrow won’t give you that guitar-strap, but feel free to widen/narrow the pattern for your own look!
Instructions:
1. Use the templates to cut out pattern pieces based on whether you have 1 1/2″ wide or 2″ wide strap. You will have (2) Strap ends and (2) Reinforcements.
2. With each Strap End wrong-side facing up, center a Reinforcement as shown with wrong sides together. Glue baste in place. It’s tempting to skip this step, but this will help your leather from stretching and distorting with time and wear.
3. With the leather needle installed, stitch 1/16″ around all four sides of the Reinforcement. Repeat with other Strap End.
4. Take Ribbon and center it on one half of the Strap End with wrong sides together, aligning it to the Reinforcement. (You may need to cut off the ribbon’s corners so they don’t hang out of the Strap Ends.) Clip or glue into place. Repeat with other Strap End.
5. Slide one Swivel Clasp onto the Strap End. Repeat with other Strap End.
5. Flip the other side of the Strap End up so it is folded in half with wrong sides together, encasing the clasp. Clip or glue together. Repeat with other Strap End.
6. Use your Zipper Foot to sew a seam to secure the Strap End onto the Swivel Clasp, sewing as close to the clasp as possible. Back-stitch well. Repeat for the other Strap End. TIP: Add washi tape under the foot if you don’t have a Teflon Zipper Foot like me.
7. Switch to a Teflon or Walking Foot and top-stitch each Strap End together with the Ribbon using the stitch guide on the template. Repeat with other Strap End.
8. Finish with rivets, if desired. Congratulations on your new guitar strap!
It doesn’t stop here! I’ve been seeing beautiful striped belt strappings used on designer bags like here on my Pinterest page. I’m already planning out my spring bags with these looks! You can use this same method to easily update any bag for the changing seasons or add new life to a great hand-me-down or thrifted find. The options are really endless. Enjoy and let me know how you like the tutorial!!!
Happy Sewing Friends!
Cristy
This post may contain affiliate links. Please visit my Disclosures page for all details.
We use cookies on our website to give you the most relevant experience on our website. By clicking “Accept,” you consent to the use of those cookies.
This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
